- #8bit fiesta controller using two players how to
- #8bit fiesta controller using two players upgrade
- #8bit fiesta controller using two players registration
In most cases this should also enable the "background" option automatically, so you don't have to select this.
#8bit fiesta controller using two players registration
If that's the case, you can either select the device if you know the MAC or simply search again.ĩ) Here it has successfully detected the name of the controller, select OK here.ġ0) Choose the "DisplayYesNo" option to complete the registration process.ġ1) Registration of the 8bitdo controller is complete and your blue LED lights should now be solid on (the FC30 Pro will glow).ġ2) You must now setup the udev rule in order for Emulation Station to "see" the controller when you restart your Raspberry Pi.ġ3) Select your controller from the list.ġ4) This then adds the rule to the file specified, you don't need to manually take any extra steps here.Īs indicated, you will need to reboot after completing these steps to make sure all the changes have taken effect.ġ5) The menu "Configure bluetooth connect mode" is optional, but using this can be very useful.ġ6) If your controller won't connect (LED change from flashing to solid) when restarting, change the mode to "boot". If you have issues with the detection of the controller, you may find it helps to press some buttons on the controller when this screen is showing.Ĩ) It may be the case that the first time the results are returned, the name of the controller doesn't show, or that the MAC address doesn't show at all.
The blue LED will flash rapidly to indicate pairing mode.Ħ) Choose the "Register and Connect to Bluetooth Device"ħ) You will then see the "Searching" screen. With the SFC30/SN30/SF30/N30/F30/NES30 (with firmware v4.0+), this is done by first powering on the controller by holding the Start button for one second until the blue LED flashes, then hold the Select button for 3 seconds. With the FC30 Pro, this is done by holding the power button (left-hand side of the base of the controller) on until the side blue lights illuminate. You need to make sure your controller is running the relevant firmware for this to work correctly, the versions are shown in this wiki article.ĥ) Make sure your controller is powered on and searching for a connection. If you want to run this via the command line, quit Emulation Station by pressing F4 on the keyboard and type this at the command line: sudo /home/pi/RetroPie-Setup/retropie_setup.shĢ) Choose the "Configuration / Tools" menu choiceģ) Choose the "bluetooth - Configure Bluetooth Devices" menu choiceĤ) Make sure the hack option is turned "off" Also, ignore step 4 and turn the hack option on.ġ) Run the RetroPie setup script, either through the Emulation Station menu option or via the command line. Please note that using the R+START mode does result in different values for the buttons themselves so it may or may not function properly if started under any different mode in the future aside from R1+START. It also may help to reset the controller by holding down the select button for 8 seconds if this does not work. PLEASE MAKE SURE IF YOU ARE USING AN 8BITDO ZERO YOU START THE CONTROLLER WITH R1+START WHEN YOU ARE COMPLETING THESE STEPS FOR AT LEAST THE FIRST TIME. A quick note about the 8bitdo Zero controller.
#8bit fiesta controller using two players upgrade
Before you upgrade your firmware or attempt to register your controller, please make sure your controller is fully charged.
#8bit fiesta controller using two players how to
Please see the 8bitdo support page for details on how to upgrade the firmware. It is not recommended to use beta firmware versions. Please make sure you are using at least RetroPie v4.0, and the controller firmware versions listed below (newer versions shouldn't cause an issue). This guide will show how to use an 8bitdo controller with RetroPie. Setting up an 8bitdo Bluetooth controller Universal Controller Calibration & Mapping Using xboxdrvĬonvert RetroPie SD Card Image to NOOBS Image Validating, Rebuilding, and Filtering Arcade ROMs